21-869 10M Ham/CB Base Antenna Your RadioShack 10M Ham/CB Base Antenna provides excellent reception of amateur radio, CB, and commercial radio signals. The antenna can handle up to 2000 watts of transmit power. Your antenna’s features include: Electrical Half-Wave Design — provides high gain. Note: To improve your antenna’s gain, you can connect an optional ground plane kit (available through your local RadioShack store) to your antenna. Three Easy-to-Assemble Sections — help you quickly and eas

2. Snap the battery into the battery terminals. Then put the battery in the compartment. 6 12-1607.fm Page 7 Friday, July 9, 1999 9:32 AM 3. Replace the cover. The BATTERY SENTINEL lights automatically if the battery needs to be replaced or is not installed. USING EARPHONES To listen in privacy, turn VOLUME to its lowest setting and plug a monaural earphone with a 1/8-inch plug into the EARPHONE jack. Your local Radio Shack store has a complete line of earphones. Listening Safely To protect your

Do not open the product’s case. ! This symbol is intended to inform you that important operating and maintenance instructions are included in the literature accompanying this product. The graphical symbols with supplemental markings are located on the bottom of the product. Features 3 12-1630.fm Page 4 Tuesday, May 9, 2000 1:31 PM ¶ Preparation CONNECTING TO AC POWER Plug the clock radio’s power cord into a standard AC outlet. As soon as you connect AC power, the display turns on and BATTERY SEN

Listeningto YourRadio The AM antenna is built-in. To improve the AM reception, rotate the clock radio. SNOOZE — lets you temporarily turn off the alarm so you can get a few extra minutes of sleep. TIMER/9— lets you temporarily silence the alarm without changing the alarm setting. ALARM— lets you set two separate daily alarms. DISPLAY/8#RADIO ON/OFFTIME Pop-up Display Screen — place your finger in the indention in the radio above the screen to stand the display screen up for easy viewing. Display

12-239 OWNER’S MANUAL Please read before using this equipment. Weatheradio® Cube INTRODUCTION Your RadioShack Weatheradio Cube receives the weather reports that are broadcast 24 hours a day by the National Weather Service. Most areas in the U.S. have special stations operated by the U.S. Weather Bureau that provide continuous weather information. These stations operate from 162.40 to 162.55 MHz. Your Weatheradio includes these features. Instant-On Touch Bar — lets you quickly turn the Weatheadio

6. To turn off the radio, turn VOLUME to the left until it clicks. USING THE ALERT MODE You can set the Weatheradio to alert you when the National Weather Service broadcasts an emergency signal, without having to listen to continuous weather updates. Follow these steps to set the radio to the alert mode. 1. To turn on the radio, turn VOLUME to the right until it clicks. The radio is in the alert mode and the alert indicator lights. Then set VOLUME to its center position. Note: If the radio is se

Please read this user’s guide before installing, setting up, and using your new weather radio. Contents Contents Package Contents ........................................................................................................ 3 Features......................................................................................................................... 3 Setup ..................................................................................................................4 Understan

The Weatheradio receives these transmissions from up to 50 miles away. The Weatheradio sounds an alarm when a weather station broadcasts a special trigger alert signal indicating a weather emergency. Your Weatheradio includes the following features: Seven Channels (1-7) - let you choose the frequency that provides the best reception. Alert Mode - sounds the siren when it detects an emergency weather situation. Siren Test Button - lets you check the alert siren. Battery-Saving Circuit - minimizes

Both are available at your local RadioShack store. Caution: You must use a Class 2 power source that supplies 6V DC and delivers 300mA. Its center tip must be set to negative and its plug must fit the recorder's DC 6V jack. Using an adapter that does not meet these specifications could damage the recorder or the adapter. 1. Set the adapter’s voltage switch to 6V. 2. Attach the Adaptaplug to the adapter’s cord with the tip set to negative. 3. Insert the adapter’s barrel plug into the recorder’s D

AC Power Connect the supplied power cord to the AC IN jack on the side of the recorder and connect the other end to a standard AC outlet. Do not force the connections, as they only fit one way. Plug the power cord into the AC IN jack before plugging it into the AC outlet, and unplug the power cord from the AC outlet before unplugging it from the AC IN jack. Vehicle Battery Power You can power the recorder from your vehicle’s cigarette- lighter socket using a 6V, 300mA DC adapter and a size B Ada