1. O-rings in trigger valve housing are damaged. 1. O-rings must be replaced & operation of safety nose must be checked. Air leaking 1. Loose screws in housing. 1. Tighten screws. between housing 2. Damaged O-ring. 2. Replace O-ring and hose. 3. Loose air fitting. 3. Tighten air fitting & use teflon tape. Air leaking between housing and cap. 1. Damaged seal. 1. Replace damaged seals. Tool skips staples 1. Excessive air pressure. 1.Reduce air pressure to tool. while discharging. 2. Air leaks. 3.
1. Open circuit in motor or loose connections. 2. Start capacitor is at fault. 3. Short circuit in motor or loose connections. 4. Incorrect fuses or circuit breakers in power supply. 1. Inspect/repair all lead connections on motor for loose or open connections. 2. Replace start capacitor. 3. Inspect all connections on motor for loose or shorted terminals or worn insulation. 4. Install correct fuses or circuit breakers. Motor overheats, stalls (resulting in blown fuses or tripped circuit). 1. Mot
Read and understand the owner's manual for your grinder and always follow all of the safety precautions and instructions for your grinder. 2. EYE/FACE PROTECTION. Always wear safety glasses or a face shield to protect yourself from flying material. 3. HAND PLACEMENT. Always keep your hands and fingers away from the spinning grinding wheel, and protect yourself from the sharp edges of the tool. 4. SECURE CLAMPING. Make sure the tool is securely clamped in the jig and that the table is firmly l
REVISED JANUARY, 2008 (BL) WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC. Printed in Taiwan Contents INTRODUCTION 2 About-Your-New-Aluma-Classic™-Fence 2 Woodstock-Service-and-Support 2 Unpacking 3 Get-To-Know-Your-Fence 3 Location-of-Controls 3 ASSEMBLY 4 Inventory 4 W1716-Installation 5 W1720-Installation 6 Installing-Metal-Extension-Wings 8 ADJUSTMENTS 9 Fence-to-Blade 9 Scale-Installation-And-Adjustment
Note—The tables slide into place easily if you lift up while you slide them into place. 4. Place a straightedge across the top of the wings, and tighten the nuts behind the edge of the extension wings to secure the wings in place. Figure 10. Extension wing box inventory. Figure 11. T-bolt and rail T-slot. Figure 12. Sliding in the wings. -8 ADJUSTMENTS The SHOP FOX® W1716/W1720 Aluma-Classic™ Fence requires little adjustment since most of the features are built in at the factory. The primary adj
5. Nails are wrong angle. 1. Use correct nails. 2. Use undamaged, clean nails. 3. Tighten magazine. 4. Replace worn or damaged parts. 5. Use correct angle nails. Nailer does not fire. 1. Nailer is not lubricated. 2. Nail is jammed in magazine or discharge area. 3. Piston shaft is damaged. 4. Air pressure too low. 1. Follow lubricating instructions. 2. Clear nailer magazine or discharge area. 3. Replace piston shaft. 4. Check/increase air pressure. Air blows out of exhaust cap; nailer will not fi
It can either be mounted to a wall or laid flat on a table or bench top. If you are planning to utilize the flashing light feature, it will be most easily visible if it is wall-mounted. The unit should be within 15 feet of the telephone receiver to allow connection of the audio sensor. You will also need access to a 110V outlet to plug in the power transformer. The unit should be located at least 5 feet away from the nearest machine(s). If the machine is too close, the ambient sound from the ma
Load the glue sticks into the back of the gun. 2: Press trigger several times until the glue stick is firmly set into the inner tube. 3: Allow the glue gun to warm up for approximately 5 minutes. 4: Squeeze trigger until glue flows from the nozzle. 5: Glue need not be spread. Press surfaces together within 15 seconds. Use of clamps or other holding devices is not necessary. Clean surfaces for best bonding. 6: Unplug glue gun when finished. No clean up required. Never pull the glue stick out
Load the glue sticks into the back of the gun. 2: Press trigger several times until the glue stick is firmly set into the inner tube. 3: Allow the glue gun to warm up for approximately 5 minutes. 4: Squeeze trigger until glue flows from the nozzle. 5: Glue need not be spread. Press surfaces together within 15 seconds. Use of clamps or other holding devices is not necessary. Clean surfaces for best bonding. 6: Unplug glue gun when finished. No clean up required. Never pull the glue stick out
Read and understand this entire document before installation to make sure the Model D3038 fits the intended application. NOTICE This switch is designed to be used only on dust collectors with standard ON/OFF toggle switches. Due to the nature of magnetic switches, the Model D3038 WILL NOT function properly if connected to a machine with this type of switch. If you are uncertain about the type of switch on your dust collector, contact the manufacturer for more information. Do not attempt to bypas