Always be sure the implement is in the proper raised position for transport. Reduce speed when transporting mounted implements to avoid bouncing and momentary loss of steering control. Plan your route to avoid heavy traffic. Watch for traffic when operating near or crossing roadways. Do not drink and drive! Turn curves or go up or down hills only at a low speed and at a gradual steering angle. Make certain that at least 20% of the tractor’s weight is on the front wheels to maintain safe steerage

STATEMENT OF POLICY It is the policy of Worksaver, Inc. to improve its products where it is possible and practical to do so. Worksaver, Inc. reserves the right to make changes or improvements in design and construction at any time, without incurring the obligation to make these changes on previously manufactured units. ATV Broadcast Seeder - Spreader Safety Instructions Assembly & Mounting Tractor Preparation Maintenance Operating Instructions Repair Parts ATTENTION! SAFETY RULES 1. Read instruc

to improve its products where it is possible and practical to do so. Worksaver, Inc. reserves the right to make changes or improvements in design and construction at any time without incurring the obligation to make these changes on previously manufactured units. Broadcast Seeder/Spreader PTO DRIVEN – 3-PT. MOUNTED Packing Maintenance Assembly & Mounting Repair Parts Operating Instructions ATTENTION! SAFETY RULES 1. Read instruction manual and make sure all operators are knowledgeable on correct

DCR-4 LRHD-7 (Rakes shown with optional gauge wheels) 3 PT. LANDSCAPE RAKE Safety Instructions Assembly & Mounting Tractor Preparation Maintenance Operating Instructions Repair Parts CAUTION THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE THOROUGHLY UNDERSTOOD BEFORE ATTEMPTING TO BEGIN ASSEMBLING THIS MACHINE 1. Select an area for assembly that is clean and free of any 6. After completing assembly, thoroughly inspect the debris which might cause persons working on the machine to be sure that all nut

Hydraulic system leak down, hydraulic system failures, mechanical failures, or movement of control levers can cause equipment to drop or rotate unexpectedly and cause severe injury or death. • Service work does not require going underneath. • Read Manual for service instructions or have service performed by a qualified dealer. WARNING! Keep all persons away from operator control area while performing adjustments, service, or maintenance. Before dismounting power unit or performing any service or

Position the tongue weldment between the front pull brackets welded to the front crosstube. Install the two 5/8” x 11/2” bolts with washers and nylock nuts as shown in the exploded parts diagram. NOTE: Nylock nuts are used at locations where some pivoting motion is expected between the bolted parts. It is suggested that nylock nuts be tightened to just a snug fit and then backed off 1 - 11/2 turns. Install the two 1/2”x 31/2” shift pins to lock the tongue weldment to the front crosstube pull bra

Periodically tighten all bolts, nuts and screws and check that all cotter pins are properly installed to ensure unit is in a safe condition. When completing a maintenance or service function, make sure all safety shields and devices are installed before placing unit in service. Never use your hands to locate a hydraulic leak on attachments. Use a small piece of cardboard or wood. Hydraulic fluid escaping under pressure can penetrate the skin. Openings in the skin and minor cuts are susceptible t

Keep load low. WARNING! For multiple spear models, always insert spears into the bale – NEVER under the bale. Failure to insert spears into bale can allow bale to roll back when loader is raised, causing serious injury or death. TRANSPORTING —————————————————— CAUTION! When traveling on public roads, whether at night or during the day, use accessory light and devices for adequate warnings to operators of other vehicles. Comply with all federal, state and local laws. Carry load low. Check visibil

WARNING! For multiple spear Models GLB-3000, GLB-330, GLB-340, always insert spears into the bale – NEVER under the bale. Failure to insert spears into bale can allow bale to roll back when loader is raised, causing serious injury or death. Always use a tractor and front loader large enough to safely handle your bales. Check your tractor and front loader to make sure they are in good working condition. Check all loader mounting bolts to make sure they are tight. Check the tractor’s hydraulic sys

Be sure tractor is properly counter-balanced with weights before attempting to lift any load with the Bale Spear attachment. If you are handling bales with both the front end loader and the 3 pt. hitch on the tractor, always load the 3 pt. attachment first and unload last. The bale spear is to be used only for handling hay bales. Do not use for digging rocks, pulling out fence, or as a craning device with a chain over the spear. LARGE ROUND BALES: Using the bucket tilt cylinders, adjust the angl