It is not always necessary or desirable to point surround speakers directly at the listening area. Doing so can often attract undue attention to them, especially when your head is turned from looking directly to the front, so experiment before investing in special brackets. 5.1 systems (figure 4) Place the speakers approximately 120. round from front centre. This will determine whether they are placed on the side or rear wall. 6.1 systems with one rear speaker (figure 5) Place the side speakers
600 Series2 DM™603 S2 and DM™604 S2 Owner's manual LISTEN AND YOU'LL SEE Figure 1 Л_л ■ il Figure 2 Figure 4 Figure 3 DM '603 S2 and DM"604 S2 Owner's manual English..........................................1 Français........................................2 Deutsch.........................................3 Español.........................................4 Português......................................5 Italiano.........................................6 Nederlands..............
They are designed to pierce through carpeting to the floor surface. Initially, screw the lock nuts fully onto the spikes and screw the spikes fully into the threaded inserts in the base of the speaker. If the cabinet rocks, unscrew the appropriate spikes until the speaker stands firmly on the floor and lock them in place by tightening the lock nuts against the base. If you do not have a carpet, use a protective disc under the spikes to protect the floor surface. AFTERCARE The cabinet surface
This can improve the resolution of low-level detail. Observe the correct polarity as before. When bi-wiring, incorrect connection can also impair the frequency response. The terminals accept 6mm (1/4-in) spades, bared wire ends or round pins up to 6mm diameter and 4mm banana plugs. When using spades, fit them under the sliding collar. Important safety notice: In certain countries, notably those in Europe, the use of 4mm banana plugs is considered a potential safety hazard, because they may be in
. . Figure 1 Figure 4 Figure 2 703 704 Figure 6 Figure 5 Figure 3 Contents English Limited Warranty...........1 Owner’s Manual............1 Francais Garantie limitee.............2 Manuel d’utilisation .......3 Deutsch Garantie .......................4 Bedienungsanleitung.....4 Espanol Garantia limitada...........6 Manual de instrucciones ................6 Portugues Garantia limitada...........8 Manual do utilizador .....8 Italiano Garanzia limitata ...........9 Manuale di istruzioni ...10 Nederl
Connect the speakers as described in section 4 before continuing. Set the required horizontal angle and push the speaker back to the wall, but leave a little clearance to avoid rattles. f Go to section 4. 3.7 DS8S The speakers may be fixed to a wall or ceiling using screws in the range 5mm to 6mm diameter (No.10 to No.12). On the back of the cabinet are three wall plates. The screw head should be inserted into the round part of the aperture and slid fully along one of the slots. The slots are sp
2 If the equipment is being used outside the country of purchase, you should contact B&W national distributor in the country of residence who will advise where the equipment can be serviced. You can call B&W in the UK or visit our web site to get the contact details of your local distributor. To validate your warranty, you will need to produce this warranty booklet completed and stamped by your dealer on the date of purchase. Alternatively, you will need the original sales invoice or other proof
Bi-wiring involves the use of two separate 2-core cables from the same amplifier, one to each pair of terminals. This is the minimum we would recommend, but should you prefer to single wire, perhaps during the initial setup procedure or because you do not want to see a multitude of cables in the room, you must connect both positive and both negative speaker terminals together. midrange, so we recommend that, when single wiring, you connect the cable from the amplifier to the terminals that direc
The relay in the speaker needs a certain amount of current to operate, so check the specification of your processor first before proceeding. You will need to draw 45mA for each speaker you want to switch. The relay in the speaker only works when the manual switch is set to the monopole (•) position. If there is no voltage to the trigger input, the speaker stays monopole. If a 12V DC signal is present, the relay overrides the manual monopole setting and switches the speaker to dipole mode. If you
The drive unit suspensions will also loosen up during the first hours of use. The time taken for the speaker to achieve its intended performance will vary depending on previous storage conditions and how it is used. As a guide, allow up to a week for the temperature effects to stabilise and 15 hours of average use for the mechanical parts to attain their intended design characteristics. However, longer run-in periods (as long as a month) have been reported and there is evidence to suggest that t