3. Insert the Handle (4) into the Handle Sockets (3) and mount the Handle Sockets to the Side Panel B (1) top using supplied hardware. Note: The Handle (4) configuration may differ slightly than what is shown in this manual. 4. Lift Side Panel B (1) all the way to expose the wire spool and Wire Feed Mechanism (11). Wire Feed Mechanism (11)Wire SpoolWire Spool Axle (10) Side Panel B (1) (C) (D) (34) – + 5. Remove the Nut from the Wire Spool Axle (10). Place the Wire Spool over the Axle with the w

There are certain applications for which this tool was designed. Do not modify this tool and do not use this tool for a purpose for which it was not intended. 17. Do not operate tool if under the influence of alcohol or drugs. Read warning labels on prescriptions to determine if your judgment or reflexes are impaired while taking drugs. If there is any doubt, do not operate the tool. 18. Pacemaker safety warning. People with pacemakers should consult with their physician(s) before using this pro

(See Figure C.) 5. If you are using one extension cord for more than one tool, add the nameplate amperes and use the sum to determine the required minimum cord size. (See Figure C.) 6. If you are using an extension cord outdoors, make sure it is marked with the suffix “W-A” (“W” in Canada) to indicate it is acceptable for outdoor use. 7. Make sure your extension cord is properly wired and in good electrical condition. Always replace a damaged extension cord or have it repaired by a qualified ele

The third prong (round) is the ground. Plug the product’s cord only into three-prong receptacles. Never cut off the round prong. Cutting off the ground will result in a safety hazard and void the warranty. #38347 Page 4 Assembly 1. The Handle for the Lid (#4) needs to be assembled. Remove nuts and washers from Handle. Place Handle in place on front portion of Lid and tighten screws with washers and nuts. 2. Attach the black plastic Filter to the Pump (#28). It fits over the wide opening on the s

When finished, release the Connecting Rod and the Bobbin Winder will reset to the ‘OFF’ position. Attaching the Needle 1. Unplug the Power Cord from the electrical outlet. 2. Select a proper needle size according to the thread count and type of material being sewn. 3. Turn the Hand Wheel until the needle bar reaches the highest point of its stroke. 4. Loosen Screw (2) and hold needle (1) with its indented part “A” facing exactly to the right in direction “B”. 5. Insert the needle and push it up

The Model and Serial numbers are located on the generator data plate on the alternator case or generator frame, along with other important information. Model Number Serial Number DOCCHI0011 1 6/14/00 Rev. 1 LIMITED 1 YEAR WARRANTY STATEMENT Harbor Freight Tools makes every effort to assure that it's Chicago Electric products meet high quality and durability standards, and warrants that this product is free from defects in materials and workmanship for the following periods (fromthe date of purch

Cigarette Lighter Socket (18) Button (15) Cigarette Lighter Recharger (18) Copper Booster Cables (11) Volt Meter (17) Light Case (2) Button Lock (16) Recharger SocketSafety SwitchAC InletPower Cord (47) The Jumpstarter System is designed for use with vehicles and boats. You will not need a host vehicle or 120 VAC power supply. You can also use this system as a portable power source of 12 VDC in remote areas or emergencies. Jump Starting Switch the Safety Switch to the OFF position. 1. Connect RE

If there is any doubt, do not operate the tool. People with pacemakers should consult their physician(s) before use. Electromagnetic fields in close proximity to heart pacemaker could cause pacemaker interference or pacemaker failure. WARNING: This product, when used for welding or similar applications, produces chemicals known to the State of California to cause cancer and birth defects (or other reproductive harm). (California Health & Safety Code § 25249.5, et seq.) The warnings, precautions,

All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions and replacement parts, please call 1-800-444-3353 THANK YOU for choosing a HARBOR FREIGHT TOOLS product. For future reference, please complete the owner’s record below: THANK YOU for choosing a HARBOR FREIGHT TOOLS product. For future reference, please complete the owner’s record below: ________

Extended 3. high volume listening can lead to permanent hearing loss. Do not wear headphones while 4. operating your detector near high- traffic areas. Be safe and pay attention to traffic. Functions and Indicators VOLUME - Sets the sound level. TUNE - Sets the sensitivity level of the unit. NOTE: Set to the lowest setting when away from any metal objects. MODE - Sets the unit to two modes: OPERATE and BATT TEST. Red Tuning Button - Press this button and set the TUNE dial to 0 to properly balanc