Standard and Metric wrench set #20 and #15 Torx driver TRAK MOUNTED CONSOLE HARDWARE: QTY: DESCRIPTION: 8 '/4-20 X 3/”Hex Head Bolt 8 /” Flat Washer 6 /” Lock Washer 8 /-20 Hex Nut INSTALLATION: PART #: GSM33001 GSM31005 GSM31026 GSM30005 1. 2. 3. 4. 5. 6. 7. Remove inner front seat mounting bolts near transmission hump. Just loosen outboard bolts. Place Z - 20 x %” Hex head bolts into under side tracks of trak mount. Position trak mount in desired location before tightening

Just loosen outboard bolts. Place Z - 20 x %” Hex head bolts into under side tracks of trak mount. Position trak mount in desired location before tightening down hump mount. Mount rear hump brackets to under side of trak. Place trak with positioned hump mount brackets over transmission hump and onto front and rear seat mount studs. Place seat bracket on top of hump mount brackets and replace seat mount bolts. Slide console up to dash and secure to trak mount with 1/4” hardware. Unit is rea

Place seat bracket on top of hump mount brackets and replace seat mount bolts. Slide console up to dash and secure to trak mount with 1/4” hardware. Unit is ready to accept equipment control heads. HUMP BRACKET MOUNTED CONSOLE HARDWARE: QTY: DESCRIPTION: PART #: 4 Z-20 x /” Carriage bolt GSM32000 4 1/4” Flat Nylon Retaining Washer GSM31322 4 Z-20 Hex Flange Serrated Nut GSM30023 INSTALLATION: 1. Remove front seat mounting bolts near transmission hump 2. Place Carriage bolts into slots

Box 2099 • Warminster, PA 18974 • 800.524.9900 / 215.957.0720(P) • 215.957.0729 (F) C-AS-INST-11-06

Box 2099 • Warminster, PA 18974 • 800.524.9900 / 215.957.0720(P) • 215.957.0729 (F) C-AS-INST-11-06

For questions regarding the set-up of your DS-DELL-100 Series/220 Series Docking Station, please contact Havis at 1-800-524-9900 or visit for additional product support and information. This Owner’s Manual applies to the following Part Numbers: DS-DELL-101 DS-DELL-101-3 DS-DELL-103 DS-DELL-221 DS-DELL-223 • NEVER STOW OR MOUNT THE DOCKING STATION DIRECTLY IN A VEHICLE AIRBAG DEPLOYMENT ZONE. • DO NOT USE COMPUTER WHILE DRIVING. • READ ALL INSTRUCTIONS THOROUGHLY BEFORE BEGINNING INSTALLATION. •

Zip Ties (4) 2. Keys (2) 3. 1/4”-20 Screws (4) 4. M5 Screws (4) Tools required for installation: • 3mm Hex Drive (For attaching Mounting Bracket to Docking Station with M5 Screws) • 5/32” Hex Drive (For attaching Mounting Bracket to Motion Device with 1/4”-20 Screws) Port Replication Capability Side Connectivity Rearward Connectivity *(Antennas for DS-DELL-101-3 only) Mouse Keyboard Antennas* (Wi-Fi, GPS, Cellular) Microphone Parallel (DB-25) VGA Display (x2) (HDMI Dongle Required) eSATA Headpho

Collect cables to secure to the mounting system (Note: mounting system not included) 8 Operation - Docking • DO NOT MATE COMPUTER TO DOCKING STATION UNLESS COMPUTER’S DOCKING CONNECTOR ACCESS DOOR IS FULLY OPEN OR DAMAGE MAY RESULT. • DO NOT FORCE LAPTOP ONTO DOCKING STATION. IF THERE IS RESISTANCE, CHECK ALIGNMENT OF COMPUTER ON DOCKING STATION. 1) To load the computer, first ensure Docking Station is unlatched by pushing the Lock to release the Latch Handle. Once Docking Station unlatches, rel

declares that their DS-DELL-100 & DS-DELL-220 SERIES DOCKING STATIONS: Are classified within the following EU Directives: EU Electromagnetic Compatibility Directive 2004/108/EC, 2009/19/EC And further conform with the following EU Harmonized Standards: EN 55022 (2006) + A1 2007, EN 55024: 1998 + A1: 2001 + A2: 2003 EN 50498: 2010 Clause 7.1 Broadband Radiated Disturbances - Quasi-Peak Clause 7.2 Narrowband Radiated Disturbances - Average Clause 7.3 Conducted Radiated Disturbances - Severity Leve