our patented four-point combustion system creates beautiful fire and unmatched efficiency that have made Quadra-fire famous. In fact, for 20 straight years, Quadra-fire has produced the cleanest-burning line of non-catalytic wood appliances available, as rated by the epa. at Quadra-fire, being environmentally-friendly isn’t a trend—it’s the tradition. Quadra-fire wood fireplace inserts are made with heavy- gauge steel and welded together for a lifetime of dependable service. Simple maintenance w

• Read, understand and follow these instructions for safe installation and operation. • Leave this manual with party responsible for use and operation. WARNING If the information in these instructions is not followed exactly, a fire may result causing property damage, personal injury, or death. WARNING HOT SURFACES! Glass and other surfaces are hot during operation and cool down. Hot glass will cause burns. • Do not touch glass until it is cooled • NEVER allow children to touch glass • Keep chil

approved grounding device. 4. The factory-built fireplace must meet (UM)84-HUD requirements for outside combustion air supply to the fireplace fire chamber and the chimney must be listed to UL103 HT or a listed UL 1777 full length 6 inch (152mm) diameter liner must be used. It must be equipped with a spark arrestor cap and the outside air must be installed on the insert. 5. In Canada, this appliance must be connected to a 6 inch (152mm) factory-built chimney conforming to CAN/ULC-S610, STANDARD

Failure to follow these instructions could result in property damage, bodily injury or even death. • Do not store or use gasoline or other fl ammable vapors and liquids in the vicinity of this or any other appliance. • Do not overfi re - If any external part starts to glow, you are overfi ring. Reduce feed rate. Overfi ring will void your warranty. • Comply with all minimum clearances to combustibles as specifi ed. Failure to comply may cause house fi re. Check building codes prior to installati

•The liner must be securely attached to the insert flue collar and the chimney top. •The air flow of the factory-built zero-clearance fireplace system must not be altered. The flue liner top support attachment must not reduce the air flow for the existing air-cooled chimney system. •No dilution air is allowed to enter the chimney. 1. Secure the fireplace damper in the open position. If this cannot be accomplished, it will be necessary to remove the damper 2. Seal damper area of chimney around ch

Shelled Field Corn (Cont’d) corn used. In cases where it is acceptable for the appliance to run full time, 100% corn will work after the fire has been started using wood pellets. When purchasing corn to burn in your appliance, read the ingredient label very carefully. Do NOT purchase fuel that contains any additives such as oils (i.e. soybean oil) and meals as it will result in poor unit performance. If you are buying corn the only ingredient that should be listed is corn. Shelled field corn mus

• By: Qualified Service Technician/Homeowner Be sure the appliance is allowed to cool, has been unplugged and the exhaust blower is off. The products of combustion will contain small particles of fly ash. The fly ash will collect in the exhaust venting system and restrict the flow of the flue gases. At start-up if there is incomplete combustion, or if there is a shutdown or incorrect operation of the appliance it will lead to some soot formation. This will collect in the exhaust venting system.

• Leavethismanualwith party responsible for use and operation. • Read,understandandfollow these instructions for safe installation and operation. WARNING If the information in these instructions is not followed exactly, a fire or explosion may result causing property damage, personal injury, or death. • Do not store or use gasoline or other flammable vapors and liquids in the vicinity ofthis or any other appliance. • What to do if you smell gas: - Do not try to light any appliance. - Donottoucha

Be sure to release air pressure from the gas line before connection is made totheappliance.Excessivepressurewilldamagethegas control and may cause a gas leak. • GasLeakTest:Makesurethegasconnectionsaretight. Turn on the gas and coat each joint with a non-corrosive gas leak check solution. Air bubbles will form indicating any leaks. DO NOT USE A FLAME OR ANY TYPE OF IGNITION SOURCE TO CHECK FOR LEAKS. All leaks must be corrected before proceeding with installation. 0 Quadra-Fire • Fogata Grande O

Clean with emery cloth or replace as required. 10. Verify millivolt output. Replace as necessary. Venting 1. Inspect venting for blockage or obstruction such as bird nests, leaves, etc. 2. Confirm that termination cap remains clear and unobstructed by plants, etc. 3. Verify that termination cap clearance to subsequent construction (building additions, decks, fences or sheds) has been maintained. 4. Inspect for corrosion or separation. 5. Verify weather stripping, sealing and flashing remains int